In 2016, the Council for the Model Aquatic Health Code formed an ad hoc committee to define the...
The Pool & Hot Tub Alliance announced this week that a supplement to the ANSI/APSP/ICC/NPC-12 2016...
The Pool & Hot Tub Alliance has awarded the 2019 Dr. R. Neil Lowry Grant to the Pueblo Department...
Biguanide, or more specifically polyhexamethylene biguanide (PHMB), is a swimming pool and spa water sanitizer used as an alternative sanitizer in place of chlorine or bromine. It is a positively charged (cationic) polymer that is normally sold as a liquid product containing 20 percent PHMB.
Like all other swimming pool and spa sanitizers, PHMB is registered with the U.S. Environmental Protection Agency. It is registered in every state for use in residential pools and spas, but public pools and spas often require additional regulatory clearances. Before using PHMB in a public pool or spa, check with the local regulatory authority to determine if clearance is required or has been granted.
Performance and efficacy of the PHMB system is not dependent on the pH of the water and it will not be degraded by sunlight or high water temperature. It is very stable in pools and spas and its concentration does not fluctuate rapidly over time.
PHMB has very mild coagulating properties and therefore may form insoluble particles with some impurities in the water. Subsequently, these insolubles are trapped in the filter as the pool water circulates. As these insolubles deposit in the filter, the backpressure may rise, eventually triggering a backwashing or filter media rinse as dictated by the filter manufacturer's specifications. In addition, the filter should be chemically cleaned at least twice a season with a PHMB-compatible product.
RELATED: ABCs of Algae
In geographical areas with long or year-round swimming seasons, more frequent chemical cleaning may be required.
Although PHMB removes some of the contaminants that enter the pool/ spa water, others are not removed. Hydrogen peroxide is used regularly to oxidize these contaminants. Currently, quaternary ammonium algaecides are used to supplement the algaestatic properties of PHMB in pools and outdoor spas. For an ideal outcome, PHMB is used as part of a sanitizing system in pools and spas and the system may be different from supplier to supplier. For both pools and spas, certain ancillary products may be used in conjunction with PHMB and hydrogen peroxide to enhance the performance of the system. You should consult an authorized dealer or the manufacturer for more information about these systems.
Certain classes of pool chemicals or treatment processes are incompatible with PHMB. These include, but are not limited to:
The pool or spa owner should consult with the supplier of PHMB if there is any question about compatibility of an auxiliary chemical or process.
PHMB is added to the pool/spa by pouring the product in the water evenly around the perimeter with the circulation system running. The core companion products (i.e., hydrogen peroxide and in some cases a compatible algaecide) are also liquids and should be added in a similar manner. The product labels provide a method for calculating the appropriate amounts for a given pool/spa volume.
In a properly maintained pool/ spa, the concentration of PHMB should be maintained between 30 - 50 ppm as a 20 percent product, or 6 - 10 ppm active PHMB. The concentration is measured using a PHMB-specific test kit used as per manufacturer's directions. When the level of PHMB falls to 30 ppm or less (usually 10 - 14 days), a "top up" dose of PHMB is added to bring the level back to 50 ppm. The product label and literature provide a method for determining the appropriate dosage. In swimming pools, a weekly or biweekly maintenance dose of a compatible algaecide is typical. The dosing requirements are provided on the product label. The oxidizer, hydrogen peroxide, is typically added on a monthly or weekly basis (monthly dosage is typically to achieve an active ingredient concentration of 27.5 ppm) according to product label directions.
NOTE: Currently, test kits measure PHMB as the product concentration, rather than the active ingredient itself. Since the typical product strength is 20 percent active ingredient, 30 – 50 ppm product corresponds to 6 – 10 ppm active PHMB.
As with all treatment regimens, proper housekeeping, maintenance and water chemistry must be maintained when using PHMB sanitizer. Consult with the PHMB manufacturer or authorized dealer for proper water chemistry parameter levels. Although the typical water balance does not affect effi cacy of PHMB, it is necessary to maintain the water balance to protect the equipment, surfaces, and swimmer's comfort in pools and spas. Typically, the following water chemistry parameter levels are recommended, but each manufacturer's recommendation may be different.
RELATED: Is it the Filter's Fault? Probably Not
Also, as with any pool sanitizer, total dissolved solids will build over time. Periodic partial drainage and replacement with fresh water is required to reduce TDS. Before converting to/from PHMB to/from another chemical treatment or process, consult your PHMB suppliermanufacturer or authorized dealer for instructions.
In order to safely use and handle PHMB and hydrogen peroxide products, all individuals involved in their production, distribution, sale, use should be trained and knowledgeable about their properties. Safety information is available on the product label, product SDS and manufacturer's training materials. This safety information will include product and packaging disposal instructions and spill response information.
In 2016, the Council for the Model Aquatic Health Code formed an ad hoc committee to define the impact of cyanuric acid on disinfection. The committee members include representatives of stabilized and unstabilized sanitizers and have a diverse range of expertise. The CMAHC Cyanurate Ad Hoc Committee has recently published its work in the journal titled Water. The article is highly technical. The following summary is being provided in terms most pool industry professionals can...
Surf's always up in Australia — at least it is in the coastal town of Yeppon in central Queensland. That's where Surf Lakes International debuted the world's largest and arguably most innovative wave pool. Once considered a novelty in the surfing community (putting it politely) Surf Lakes has taken the concept of a wave...
You've already got your website up and running, you've got online adverts going and you're doing your best to promote yourself in the local community — but you're still not performing as well as your competitors! What more can you do to promote your business?
With social media and Google ruling the roost when it comes to promoting businesses online, you're going to need a completely new approach to replace the old tactics of newspaper ads, radio and event appearances.
Many of us may have had the unfortunate experience of adding soda ash "wrong" to pool water, resulting in a pool that looks like it is filled with milk. In fact, we refer to it as "milking" a pool. Why does that happen?
When we decide, for example, to raise the pH of a pool from 7.2 to 7.6, we calculate how much soda ash is required for that size pool to achieve a 0.4 pH unit increase. A solution of soda ash (sodium carbonate) has a pH of above 11, so when added to pool water the pH...